Topsetter 74 / Acento II / Screen PT-R4xxx


 Error:            Description:
 Ex101
   Nip roller does not ascend
 Ex102    Nip roller does not descend
 Ex103    Transport unit does not ascend
 Ex104    Transport unit does not descend
 Ex105    Trail clamp arm does not ascend
 Ex106    Trail clamp arm does not descend
 Ex107    Squeeze roller does not descend
 Ex108    Squeeze roller does not ascend
 Ex109    Trail clamp cannot be locked. PH24-1/2 or M24 is illegal
 Ex10a    Trail clamp cannot be unlocked. PH24-1/2 or M24 is illegal
 Ex10b    Balancer drive pin cannot be initialized
 Ex10c    Both of the Home and Away side drive pins for the balancer can not be pulled out
 Ex10d    Both of the Home and Away side drive pins for the balancer can not be inserted
 Ex10e    Bar for releasing the lead clamp does not ascend
 Ex10f    Bar for releasing the lead clamp does not descend
 Ex110    Shutter does not open
 Ex111    Shutter does not close
 Ex112    Plate size (in the Y direction) is shorter than the set value
 Ex113    When the plate is unloaded, the plate pass sensor (PH54-2) does not switch to ON
 Ex114    Not bring down squeeze at loading
 Ex115    Plate size (in the Y direction) is longer than the set value
 Ex116    Servo status is illegal
 Ex117    Servo status is error
 Ex118    Servo alarm
 Ex11a    Drum speed is set beyond the permitted rate of the servo controller
 Ex11b    Current drum's encoder pulse is beyond 4000
 Ex11c    Error has occurred during drum positioning
 Ex11d    When the clamp is locked, some tail clamps are detected on the clamp arm, or when the clamp is unlocked, some tail clamps are not detected on the clamp arm
 Ex11e    Drum's encoder pulse is beyond the permitted range after drum positioning
 Ex11f    Plate cannot be transferred into the transport unit
 Ex120    Home side balancer pin cannot be detected before insertion
 Ex121    Home side balancer pin cannot be detected before pulled out (The balancer is not moving).
 Ex122    Clamp arm and squeeze roller do not descend
 Ex123    Trail clamp is half-locked
 Ex124    The plate passing-sensor for unloading (PH54) does not switch to ON
 Ex125    Time-out error has occurred when the squeeze roller ascends and clamp cam
 Ex126    There was no plate to move to the shutter
 Ex127    Servo controller does not enter the "Ready" status
 Ex128    The balancer search sensor has not detected a balancer
 Ex129    Error has occurred on the Home side of the alignment plate (while the alignment plate is returning to its origin)
 Ex12a    Error has occurred on the Away side of the alignment plate (while the alignment plate is returning to its origin)
 Ex12b    Error has occurred on the Home and Away sides of the alignment plate (while the alignment plate is returning to its origin)
 Ex12c    Error has occurred on the Home side of the alignment plate (while alignment is performed)
 Ex12d    Error has occurred on the alignment plate (while alignment is performed)
 Ex12e    Error has occurred on the Home and Away sides of the alignment plate (when alignment is performed)
 Ex12f    Plate has not transferred to the punch unit
 Ex130    Plate does not leave the punch unit
 Ex131    Time-out error has occurred when Punch 1 is activated
 Ex132    Time-out error has occurred when Punch 2 is activated
 Ex133    Time-out error has occurred when Punch 3 is activated
 Ex134    Time-out error has occurred when Punch 4 is activated
 Ex135    Time-out error has occurred when Punch 5 is activated
 Ex136    Time-out error has occurred when Punch 6 is activated
 Ex137    Time-out error has occurred when Punch 7 is activated
 Ex138    Time-out error has occurred when Punch 8 is activated
 Ex139    After a plate is transferred to the gripper clamp, the plate detection sensor (PH29H/A) does not switch to ON
 Ex13a    When the clamp arm is lowered, the sensor (to detect whether the clamp arm pins are hooked on the clamp properly) has been turned ON.(Home side)
 Ex13b    The specified encoder pulse for the drum is beyond 4000
 Ex13c    The transport unit's Away side is not moving during its operation
 Ex13d    The transport unit's Home side is not moving during its operation
 Ex13e    Error has occurred on the Home side of the alignment plate (while the alignment plate is finely returning to its origin)
 Ex13f    Error has occurred on the Away side of the alignment plate (while the alignment plate is finely returning to its origin)
 Ex140    Error has occurred on the Home and Away side of the alignment plate (while the alignment plate is returning to its origin)
 Ex141    A plate remains in the transport unit when the machine received a request command
 Ex142    A plate remains in the transport unit during error handling
 Ex143    A plate remains on the discharge table in the transport unit
 Ex144    A plate remains on the insertion table in the transport unit
 Ex145    Plate cannot be moved onto the discharge table during initialization
 Ex146    Plate cannot be moved onto the insertion table
 Ex147    Balancer search operation has not been completed properly
 Ex148    When the transport unit descends, only the Home side Down sensor in the transport unit is turned ON
 Ex149    When the transport unit descends, only the Away side Down sensor in the transport unit is turned ON
 Ex14a    When the transport unit ascends, only the Home side UP sensor in the transport unit is turned ON
 Ex14b    When the transport unit ascends, only the Away side UP sensor in the transport unit is turned ON
 Ex14c    Front, rear or side cover is open. (Some interlock switches are OFF)
 Ex14d    A fuse on the relay board was blown. (home)
 Ex14e    Thumbscrew is not tightened securely on the rear cover. (The servo stop switch is ON)
 Ex14f    A plate exists on the discharge table in the transport unit during initialization
 Ex150    A plate exists on the insertion table in the transport unit during initialization
 Ex151    Number of balancers is not sufficient. (The number of balancers checked by the balancer search sensor was one, two or three for both the Home and Away sides)
 Ex152    Clamp arm is not in the UP position
 Ex153    A fuse on the relay board was blown. (away)
 Ex154    Blower is turned off, but signal does not change
 Ex155    Tail clamps are missing during initialization
 Ex156    The size check program of the cetering function detects that the measured plate size is longer than the expected one
 Ex157    The size check program of the cetering function detects that the measured plate size is shorter than the expected one
 Ex158    Both of Home and Away size check sensors are on before starting the centering program
 Ex159    Auto-loader is stopped by a interlock OFF
 Ex15a    This hardware matching is illegal
 Ex15b    The balancer is not moved to the target position
 Ex15c    The drum can not be spun up because the Home-Upper sensor of the Lead clamp release bar is off
 Ex15d    During plate loading, double plate loading is detected
 Ex15e    The loaded plate is detected to be floating while drum spinning
 Ex15f    The drum cannot be spun up because the Upper sensor of the clamp arm is off
 Ex160    The drum can not be spined up because the Home-Upper sensor of the clamp arm is off
 Ex161    The drum cannot be spun up because the balancing pin on the (Away side) is not in the waiting position
 Ex162    The drum cannot be spun up because the balancing pin on the (Home side) is not in the waiting position
 Ex163    The drum cannot be spun up because the Upper sensor of the squeeze roller is off
 Ex164    The drum can not be spun up because the Away-Upper sensor of the Lead  clamp release bar is off
 Ex165    The drum is rotated to the "lead clamp position", but the status of the Servo controller (SVC) has not changed to "Ready"
 Ex166    The drum is rotated to the "tail clamp position", but the status of the Servo controller (SVC) has not changed to "Ready"
 Ex167    The drum is rotated to the "squeeze position", but the status of the Servo controller (SVC) has not changed to "Ready"
 Ex168    The drum is rotated to the "balance pin before inserted", but the status of the Servo controller (SVC) has not changed to "Ready"
 Ex169    The drum is rotated to the "balance pin after inserted", but the status of the Servo controller (SVC) has not changed to "Ready"
 Ex16a    The drum is rotated to the "pick up tail clamp position", but the status of Servo controller (SVC) has not changed to "Ready"
 Ex16b    The drum is rotated to the "plate removal position", but the status of the Servo controller (SVC) has not changed to "Ready"
 Ex16c    SVC Error has occurred during drum positioning for the lead clamp
 Ex16d    SVC Error has occurred during drum positioning for the tail clamp
 Ex16e    SVC Error has occurred during drum positioning for the squeeze
 Ex16f    SVC Error has occurred during drum positioning for the balance pin insertion
 Ex170    SVC Error has occurred during drum positioning for the balance pin pull out
 Ex171    SVC Error has occurred during drum positioning for the picking up tail clamp
 Ex172    SVC Error has occurred during drum positioning for the plate removal
 Ex173    Time-out error has occurred during drum positioning (Lead clamp position)
 Ex174    Time-out error has occurred during drum positioning (Tail clamp position)
 Ex175    Time-out error has occurred during drum positioning (Squeeze position)
 Ex176    Time-out error has occurred during drum positioning (Balance pin before inserted)
 Ex177    Time-out error has occurred during drum positioning (Balance pin after inserted)
 Ex178    Time-out error has occurred during drum positioning (Pick up tail clamp)
 Ex179    Time-out error has occurred during drum positioning (Plate removal)
 Ex17a    After verifying the removal of the plate, press the OK button. When the OK button is pressed, initialization begins
 Ex17b    PH62A-sensor is illegal. The sensor detects a plate during initialization
 Ex17c    PH29H-sensor is illegal. The PH29H-sensor does not turn ON during initialization
 Ex17d    PH61H-sensor is illegal. The sensor detects a plate during initialization
 Ex17e    PH61A-sensor is illegal. The sensor detects a plate during initialization
 Ex17f    PH29A-sensor is illegal. The PH29A-sensor does not turn ON during initialization
 Ex180    Drum does not start rotating at high-speed
 Ex181    Drum does not rotate at the specified high-speed
 Ex182    Error has occurred after the drum rotated at the specified high-speed
 Ex183    Drum cannot be stopped when rotating at high-speed
 Ex184    Drum operation is stopped with an emergency stop command
 Ex185    Drum operation is stopped with an abort command
 Ex186    Drum's vacuum pressure is not sufficient. Please confirm connection of the blower-hose, or the Vacuum-sensor is illegal
 Ex187    Error has occurred on the blower, or the power supply of the blower is OFF
 Ex188    Drum operation is stopped due to low pressure in the drum
 Ex189    Door is open
 Ex18a    Door does not open
 Ex18b    Transport tasks: Parameter error
 Ex18c    Error has occured on the blower. Please turn off this machine, and turn on after waiting 10 seconds. Also, confirm whether or not the connector doesn't come off
 Ex18d    The drum can not be spun up, because some of the interlock switches are OFF, or some of the actuator's sensors are damaged, or the blower is damaged
 Ex18e    Door does not open, because some of the interlock switches are OFF (front cover or rear cover is open)
 Ex190    Clamp arm does not descend (Home side)
 Ex191    Clamp arm does not descend (Away side)
 Ex192    Clamp arm does not ascend (Home side)
 Ex193    Clamp arm does not ascend (Away side)
 Ex194    When the clamp arm is lowered, the sensor (to detect whether the clamp arm pins are hooked on the clamp properly) has been turned ON (Away side)
 Ex195    Trail clamp cannot be locked (Home side)
 Ex196    Trail clamp cannot be locked (Home side)
 Ex197    Trail clamp cannot be unlocked (Home side)
 Ex198    Trail clamp cannot be unlocked (Away side)
 Ex199    Balancer drive pin cannot be inserted (Home side) Either of PH11-1H,PH11-2H or M11H is illegal
 Ex19a    Balancer drive pin cannot be inserted (Away side) Either of PH11-1A,PH11-2A or M11A is illegal
 Ex19b    Balancer drive pin cannot be pulled out (Home side) Either of PH11-1H,PH11-2H or M11H is illegal
 Ex19c    Balancer drive pin cannot be pulled out (Away side) Either of PH11-1A,PH11-2A or M11A is illegal
 Ex19d    Balancer pin cannot be detected before insertion (Away side)
 Ex19e    Balancer pin cannot be detected before pull out (the balancer is not moving) (Away side)
 Ex19f    The balancer search sensor has not detected a balancer.(Home side)
 Ex1a0    The balancer search sensor has not detected a balancer.(Away side)
 Ex1a1    Number of balancers is not sufficient. (Home side)
 Ex1a2    Number of balancers is not sufficient. (Away side)
 Ex1a3    Soft-interlock or drum-stop swtich is OFF during drum spinning
 Ex1a4    The cover-interlock switch is OFF during drum 
spinning Ex1a5    The interlock switch-3 is OFF during drum spinning
 Ex1a6    A plate cannot be carried into the transport unit
 Ex1a7    A plate cannot be carried to sensor PPH50-2
 Ex1a8    Auto-loader is not turned on, or some interlock switches on Auto-loader are OFF. Please turn on Auto-loader, or all interlock switch
 Ex1a9    Cassete carrier was removed. Please set cassette carrier
 Ex1aa    The door of the cassette part is open
 Ex1ab    Maintenance-cover of Auto-loader was opend. Please clode maintenance cover
 Ex1ac    Bridge cover-2 was opened. Please clode bridge cover-2
 Ex1ad    An interleaf under a plate was detected. Or a plate size (in the Y direction) is shorter than the set value
 Ex1ae    An interleaf was detected on a plate. Or a plate size (in the Y direction) is shorter than the set value
 Ex1b0    Trail clamp is not detected on the clamp arm before the plate loading
 Ex1b1    Trail clamp is detected on the clamp arm before the plate unloading
 Ex1b2    Trail clamp cannot be set correctly
 Ex1b3    This plate can't be transed. Because something error has occured when the transfering to AT
 Ex1b4    This plate can't be transed. Because trans path position is down
 Ex1b6    The bridge-passing sensor does not turn OFF (for Jig mode)
 Ex1b7    A plate remains on the plate detection sensor(PH70)
 Ex1b8    When detects the front of a plate, the detection area is not brought
 Ex1b9    When detects the front of a plate, the detection of Home or Away is not brought
 Ex1ba    PH11-2H-sensor is illegal. The PH11-2H-sensor does not turn ON during initialization
 Ex1bb    PH11-2A-sensor is illegal. The PH11-2A-sensor does not turn ON during initialization
 Ex1c0    Lead clamp release bar cannot be driven. Either PH30H or PH31H is illegal
 Ex1c1    Lead clamp release bar cannot be driven. Either PH30H or PH31H is illegal
 Ex1c2    Trans path cannot be driven. Either PH55, PH56, or PH57 is illegal
 Ex1c3    Trans path cannot be driven. Either PH56, or, PH57 is illegal
 Ex1c4    Trans path cannot be driven. Either PH55, or, PH56 is illegal
 Ex1c5    Trans path cannot be driven. Either PH55, or, PH57 is illegal
 Ex1c6    Trail clamp arm cannot be driven. Either PH20 or PH21 is illegal
 Ex1c7    Trail clamp arm cannot be driven. Either PH20 or M20 is illegal
 Ex1c8    An interleaf was detected under a plate
 Ex1c9    When centering alignment is performed, the plate set position is out of range
 Ex1ca    Error has occured on the punching unit. The punch hole could not be opened correctly
 Ex1cb    Opened shutter obstructs trans path driving
 Ex1cc    Trail clamp arm obstructs trans path driving
 Ex1cd    A plate remains in a machine
 Ex1d0    Transfer operation is halted with an abort command
 Ex1d1    Transport tasks are being processed
 Ex1d2    Transport tasks are not being processed
 Ex1d3    Transport tasks: Message order error
 Ex1d4    Transport system is not initialized
 Ex1e0    SVC user parameter breakdown
 Ex1e1    SVC user parameter setting error
 Ex1e2    SVC over-current
 Ex1e3    SVC detection of regenerative error
 Ex1e4    SVC postion error pulse overflow
 Ex1e5    SVC Main circuit voltage error detection
 Ex1e6    SVC over speed
 Ex1e7    SVC overloaded (high load)
 Ex1e8    SVC overloaded (low load)
 Ex1e9    SVC stauts 99h
 Ex1ea    SVC heat sink has overheated
 Ex1eb    SVC stauts b1h
 Ex1ec    SVC is out of control
 Ex1ed    SVC phase error has been detected in the encoder
 Ex1ef    SVC A and B phase for the encoder has broke down
 Ex1f0    SVC C phase for the encoder has broke down
 Ex1f1    SVC some phases of power line is open
 Ex1f3    SVC An instantaneous loss of power has occurred
 Ex1f4    SVC unknown error
 Ex200    Exposure operation is interrupted with an abort command
 Ex201    Exposure processing task is now processing another command
 Ex202    Cancellation was requested while processing was not being performed
 Ex203    PGON is not asserted
 Ex204    START signal is not asserted
 Ex205    START signal is not negated
 Ex206    Test pattern; Data is not transferred
 Ex207    Test pattern; Data transfer is not completed
 Ex208    Reset procedure for RB31 board is not completed
 Ex209    The set value for the drum rotation speed is too large
 Ex20a    No plate edge is detected (when the plate edge sensor moves to the Away side)
 Ex20b    No plate edge is detected (when the plate edge sensor is returning to the Home side)
 Ex20c    Recording head has traveled beyond the limit (on the Away side)
 Ex20d    Recording head has traveled beyond the limit (on the Home side)
 Ex20e    Recording head positioning range error
 Ex20f    Recording head has not been positioned at its origin. (Origin sensor does not turn OFF)
 Ex210    Recording head has not been positioned at its origin. (Origin sensor does not turn ON)
 Ex211    Emergency stop is requested for the secondary-scanning motor
 Ex212    Secondary-scanning motor is deactivated with an abort command
 Ex213    Secondary scanning motor is illegal
 Ex214    Exposure in the secondary scanning direction exceeds the effective image ouput range
 Ex215    FPGA sequence error
 Ex216    Time-out error has occurred when the secondary scanning motor is activated
 Ex217    EZ search has not detected the ORG sensor
 Ex218    EZ search has not detected the EZ sensor
 Ex219    When the CAL sensor search was executed, the maximum light intensity was less than 50 mW
 Ex21a    Light intensity at the measurement starting point was at maximum when the CAL sensor search was executed
 Ex21b    Light intensity at the measurement end point was at maximum when the CAL sensor search was executed
 Ex21c    Over travel at recording head's Home side when the CAL sensor search was executed
 Ex21d    Test pattern parameter error
 Ex21e    PGON signal is not negated
 Ex21f    Secorndary direction origin point setup procedure failure.(The calibrated origin point is not the same as logical origin point)
 Ex220    After an image data transfer from RIP is interrupted, it isn't resumed
 Ex221    Drum rotation error was detected. This plate will be unloaded because it could not be exposed correctly
 Ex300    Both of plate pad and paper pad are not in original point
 Ex301    After an interleaf is removed, plate cannot be detected
 Ex302    An interleaf was detected on a plate. Or a plate size (in the Y direction) is shorter than the set value
 Ex303    Plate pad cannot be initialized
 Ex304    Plate pad cannot carry a plate
 Ex305    While carring a plate, the plate pad dropped the plate
 Ex306    Paper pad cannot be initialized
 Ex307    Air pressure in the plate pad does not go down
 Ex308    Air pressure in the paper pad does not go down
 Ex309    PCL time-out error has occurred when plate pad was moved
 Ex30a    PCL time-out error has occurred when paper pad was moved
 Ex30b    Time-out error has occurred when plate pad was moved by stepping
 Ex30c    Time-out error has occurred when paper pad was moved by stepping
 Ex30d    A plate cannot be carried into the transport unit
 Ex30e    PH90 does not switch to ON while removing the interleaf
 Ex30f    PH90 does not switch to OFF while removing the interleaf
 Ex310    Maintenance cover of auto-loader is open. Please close maintenance cover
 Ex311    Bridge cover-2 of auto-loader is open. Please close bridge cover-2
 Ex312    Cassette carrier is not set. Please set cassette carrier
 Ex313    A plate remains in the bridge unit
 Ex314    An interleaf remains in the paper exit
 Ex315    Nip roller does not ascend
 Ex316    Nip roller does not descend
 Ex317    Auto-loader is not turned on, or some interlock switches on Auto-loader are OFF. Please turn on Auto-loader, or all interlock switch
 Ex318    A plate cannot be carried to the bridge-passing sensor
 Ex319    The plate pad went down from the original point
 Ex31a    The paper pad went down from the original point
 Ex31b    Maintenance-cover of Auto-loader was opend. Please clode maintenance cover
 Ex31c    Bridge cover-2 was opened. Please clode bridge cover-2
 Ex31d    Door was opened. Please close the door
 Ex31e    Cassete carrier was removed. Please set cassette carrier
 Ex31f    The paper pad dropped the interleaf while carrying the it
 Ex320    Plate pad dropped a plate before the plate pad reached the intermediate sensor
 Ex321    An interleaf in front of a plate was detected
 Ex322    A plate remains on the sensor-2 of the bridge
 Ex323    Intermediate sensor is OFF
 Ex324    Power switch was turned off while Auto-loader was moving
 Ex325    A plate cannot be carried to the intermediate sensor
 Ex326    An interleaf under a plate was detected. Or a plate size (in the Y direction) is shorter than the set value
 Ex327    The bridge-passing sensor does not turn OFF (for Jig mode)
 Ex328    Door is open
 Ex32c    The nip-roller for paper discharge cann't be opened
 Ex340    Door is open
 Ex341    The interlock switch-3 is OFF
 Ex342    The interlock switch-2 is OFF
 Ex343    The interlock switch-1 is OFF
 Ex344    A fuse on the relay board at home side has blown
 Ex345    A fuse on the relay board at away side has blown
 Ex346    Nip roller does not descend
 Ex347    Nip roller does not ascend
 Ex348    Shutter does not open
 Ex349    Shutter does not close
 Ex360    A plate remains on the bridge's sensor-1
 Ex361    No plate exists on the bridge's sensor-3
 Ex362    A plate remains on the bridge's sensor-3
 Ex363    A plate size in the Y direction is too long when its transferring to the AT
 Ex364    A plate size in the Y direction is too short when its transferring to the AT. Or an interleaf in front of a plate was detected
 Ex365    After the paper pad is descended, the metal sensor does not switch to ON
 Ex366    Plate pad dropped the plate, before this initialize
 Ex367    A teaching of plate size in the Y direction (1st) is finished
 Ex368    A teaching of plate size in the Y direction (2nd) is finished
 Ex369    This plate can't be transed. Because something error has occured when transfering to AT
 Ex36a    Air pressure in the plate pad does not go down after retry
 Ex36b    A plate remains on the insertion table in the transport unit
 Ex36c    This plate is judge as a paper during judgement operation
 Ex36d    This plate can't be transed. Because trans path position is down
 Ex380    The door of the cassette part is open
 Ex381    Time-out error has occurred when lift was initialized
 Ex382    Time-out error has occurred when lift was moved
 Ex383    Though the lift was initialized, the origin sensor is not ON
 Ex384    The lift is not in the position where it is specified
 Ex385    Already, there has been a cassette on the lift
 Ex386    There are some cassettes which aren't being set properly
 Ex387    MA-L can't be initialized because some cassettes are not in the lift or the cassette properly
 Ex388    There is no cassette in the specified cassette slot
 Ex389    There is no cassette on the lift
 Ex38a    Lift has traveled beyond the limit (on the Up side)
 Ex38b    Lift has traveled beyond the limit (on the Down side)
 Ex38d    A cassette is already in the place to return a cassette
 Ex38e    A lift can't be raised and lowered because some cassettes are not in the lift or the cassette properly
 Ex38f    Time-out error has occurred when a cassette was moved to cassette part
 Ex390    Time-out error has occurred when a cassette was moved to lift
 Ex391    Either plate pad or paper pad is not in original point
 Ex392    An ineffective cassette number was indicated
 Ex393    Cassette has traveled beyond the limit (on the Lift side)
 Ex394    Cassette has traveled beyond the limit (on the Cassette side)
 Ex395    MA-L can't be initialized because some cassettes can't be returned to the origin
 Ex396    Though there is a cassette on the lift, the place to return the cassette isn't vacant
 Ex397    Though the movement of the lift was finished, the lift position sensor at the target position is not on
 Ex398    MA-L Servo alarm
 Ex399    Time-out error has occurred when arm was moved
 Ex39a    Time-out error has occurred when a cassette was moved to cassette part by arm
 Ex39b    Arm jut-out sensor (LS210E) is off
 Ex39c    A cassette is in illegal position of the cassette slot
 Ex39d    Arm is not in original point
 Ex39e    SQ210A sensor is illegal
 Ex400    Plate has already been loaded
 Ex401    Plate has not been loaded
 Ex402    Door is open
 Ex403    Dump interleaves from the collection box
 Ex600    Either the conveyor, processor, or stocker is not turned on, or is in the busy status or error status
 Ex601    Either the conveyor, processor, or stocker is not turned on, or is in the busy status or error status
 Ex602    The plate cannot be transferred into the AT unit
 Ex603    The plate cannot be transferred completely into the AT unit
 Ex606    Error
 Ex607    Busy
 Ex608    Error
 Ex609    Busy
 Ex60a    Error
 Ex60b    Busy
 Ex60c    Error occurred in ATM while a plate was carried to ATM
 Ex80c    The result of the calculation "Initial value + increment value * (repetition - 1)" exceeds the upper limit value
 Ex80d    (The result of the calculation "Exposure starting point + (pattern width + gap) * (repetition - 1)" exceeds the plate size
 Ex80e    The specified plate is not linked with the printing-machine's data
 Ex80f    Perform initialization at the service screen
 Ex810    No plate is set at inlet of transport unit
 Ex811    Plate (printer) size specified by the host computer is not registered
 Ex812    Image size specified by host computer is larger than allowable output image size
 Ex813    Current offset of printing machine settings cause image to extend off plate
 Ex814    Current paper-position of printing machine settings cause image to extend outside of allowable exposure area
 Ex816    Some LD is nearing the end of its usable life
 Ex817    There are some punch blocks, which have been used for more than the endurance time
 Ex819    It failed to read the cassette number. It considers that the cassette number is No.1
 Ex81a    Some LD's cannot be calibrated to the target power. These LD's be calibrated to lower target power
 Ex81b    Some LD's cannot be calibrated to the target power. Temporary to work half channels of recording head
 Ex81c    Some LD's cannot exposed by setting power due to be calibrated to lower target power
 Ex81d    The temperature of the environment is greater than 28degrees
 Ex81e    The temperature of the environment is less than 18degrees
 Ex81f    Sensor for the temperature of the environment has not been connected
 Ex820    Trail clamps are nearing the end of its usable life
 Ex821    Trail clamps have been used for more than the endurance time
 Ex822    Backup/restore of the data on NVRAM can't be performed, because the Dip-Sw 2 is not on
 Ex823    The backup of the data on NVRAM is not in Flash-Memory
 Ex824    Calibration must be done because there is some LD which doesn't reach the target power. But, LD calibration can not processed because temperature of LD block is too low
 Ex825    The direction where a connected conveyer can't be changed is set up in the plate types setting
 Ex826    No response was returned from the conveyor
 Ex827    An error was returned from the conveyer toward the switching command
 Ex828    The conveyer can't be changed to the direction that is set up in the plate types setting
 Ex82a    Since the light intensity of laser diodes is detected as having deviated more than +-5% from the specified value, the equipment executes the calibration
 Ex82b    Communication with the RAS server was interrupted. (RAS server was turned off, or RS-232C cable was drawn out)
 Ex82c    No response come from DNS
 Ex82d    Communication with the RAS server has resume
 Ex82e    It failed in the connection to the rotating light server
 Ex82f    The name of the mail server isn't right
 Ex830    It failed in the connection to the mail server
 Ex831    Mail account was rejected
 Ex832    An error occurred in the transmission of DATA command
 Ex833    An error occurred in the transmission of header
 Ex834    An error occurred in the transmission of body
 Ex835    An error occurred in the transmission of attached file
 Ex836    An error occurred in the transmission of TO command
 Ex837    A command was sent to the SMTP server. But, no answer was returned from the server
 Ex839    The cable between RB31 board and recording head is disconnected
 Ex880    Servo pack: Time-out error occurred while receiving data
 Ex881    Servo-Pack:Address error
 Ex882    Servo-Pack:Data error
 Ex883    Servo-Pack:Check sum error
 Ex884    Servo-Pack:Undefined error code
 Ex885    Servo-Pack:Number of received characters are insufficient
 Exe01    Excessive current in the LD drive (driver 1 board)
 Exe02    Excessive current in the LD drive (driver 2 board)
 Exe03    Excessive current in the LD drive (driver 3 board)
 Exe04    Excessive current in the LD drive (driver 4 board)
 Exe05    Driver board temperature error or Head FPGA Version Error
 Exe06    -5 V power supply error
 Exe07    Calibration sensor is not connected
 Exe08    Offset error in the calibration sensor
 Exe09    Irregular 5 V power supply
 Exe0a    Irregular +15 V power supply
 Exe0b    Irregular -15 V power supply
 Exe0c    Irregular 24 V power supply
 Exe0d    Cover switch is OFF
 Exe0e    BL command error (counter value is 0)
 Exe0f    Zoom sensor is not detecting
 Exe10    Focus sensor is not detecting
 Exe11    Time has expired for home return.(Zoom or focus motor)
 Exe12    Power supply irregular while the motor is driving
 Exe13    Pulse motor has traveled beyond the limit. (Zoom or focus motor)
 Exe14    Irregular power supply(instantaneous loss)
 Exe20    Temperature of the LD block is greater than 28degrees
 Exe21    Temperature at the periphery of the optical unit is greater than 35degrees
 Exe22    Temperature of the radiating fin of the Peltier element is greater than 55 degrees
 Exe23    Dew condensation error
 Exe24    Sensor for LD block has not been connected
 Exe25    Sensor for the periphery of the optical unit has not been connected
 Exe26    Sensor for the radiating fin of the Peltier element has not been connected
 Exe27    The dew condensation detection sensor has not been connected
 Exe28    Temperature of the LD block is low
 Exe30    Power supply error occurred when the recording head received the DW command
 Exe31    Command error occurred when the recording head received the DW command
 Exe32    Download error occurred when the recording head received the DP command
 Exe33    Download error occurred when the recording head received the DP command
 Exe34    Download address error occurred
 Exe35    Error occurred when the recording head received the BU command
 Exe36    Error occurred when the recording head received the BD command
 Exe40    Writing error occurred when the recording head received the AC command
 Exe41    Writing error on EEPROM
 Exe42    RAM error
 Exe43    ROM check sum error
 Exe44    FPGA error
 Exe45    Data error due to a divide-by-zero error
 Exe60    LD Current setting Error
 Exe61    The temperature of the LD block is greater than 28degrees
 (Temperature at the periphery of the optical unit > 35degrees. Temperature of the environment <= 28degrees)"
 Exe62    The temperature of the LD block is greater than 28degrees (Temperature at the periphery of the optical unit <= 35degrees. Temperature of the environment > 28degrees)"
 Exe63    The temperature of the LD block is greater than 28degrees
 (Temperature at the periphery of the optical unit <= 35degrees. Temperature of the environment > 28degrees)"
 Exe64    The temperature at the periphery of the optical unit is greater than 35degrees
 (Temperature of the environment <= 28degrees)
 Exe65    The temperature of the radiating fin is greater than 55degrees
 (Temperature at the periphery of the optical unit>35degrees. Temperature of the environment <= 28degrees)
 Exe66    The temperature of the radiating fin is greater than 55degrees
 (Temperature at the periphery of the optical unit <= 35degrees)
 Exe67    The LD block has dew. (Temperature of the LD block < 22degrees
 Temperature at the periphery of the optical unit >= 18degrees)
 Exe68    The LD block has dew. (Temperature of the LD block < 22degrees
 Temperature at the periphery of the optical unit < 18degrees)
 Exe69    The temperature of the LD block is less than 5degrees
 (Temperature at the periphery of the optical unit >= 17degrees)
 Exe6a    The temperature of the LD block is less than 5degrees
 (Temperature at the periphery of the optical unit < 17degrees. Temperature of the environment >= 18degrees)
 Exe6b    The temperature of the LD block is greater than 28degrees 
 (Temperature at the periphery of the optical unit > 35degrees. Temperature of the environment <= 28degrees)
 Exe6c    The temperature of the LD block is greater than 28degrees
 (Temperature at the periphery of the optical unit <= 35degrees. Temperature of the environment > 28degrees)
 Exe6d    The temperature of the LD block is greater than 28degrees
 (Temperature at the periphery of the optical unit <= 35degrees. Temperature of the environment <= 28degrees)
 Exe6e    The temperature inside the machine is greater than 35degrees
 (Temperature of the environment <= 28degrees)
 Exe6f    The temperature of the radiating fin is greater than 55degrees
 (Temperature at the periphery of the optical unit>35degrees. Temperature of the environment <= 28degrees)
 Exe70    The temperature of the radiating fin is greater than 55degrees
 (Temperature at the periphery of the optical unit <= 35degrees.)
 Exe71    It is just before a recording head has dew
 (Temperature of the LD block < 22degrees. Temperature of the environment >=18degrees)
 Exe72    It is just before a recording head has dew
 (Temperature of the LD block < 22degrees. Temperature of the environment < 18degrees)
 Exe73    The temperature of the LD block is in between 5degrees and 17degrees
 (Temperature of the environment <= 18degrees)
 Exe74    The temperature of the LD block is in between 5degrees and 17degrees
 (Temperature of the environment < 18degrees.)
 Exea0    Light intensity adjustment error 0ch
 Exea1    Light intensity adjustment error 1ch
 Exea2    Light intensity adjustment error 2ch
 Exea3    Light intensity adjustment error 3ch
 Exea4    Light intensity adjustment error 4ch
 Exea5    Light intensity adjustment error 5ch
 Exea6    Light intensity adjustment error 6ch
 Exea7    Light intensity adjustment error 7ch
 Exea8    Light intensity adjustment error 8ch
 Exea9    Light intensity adjustment error 9ch
 Exeaa    Light intensity adjustment error 10ch
 Exeab    Light intensity adjustment error 11ch
 Exeac    Light intensity adjustment error 12ch
 Exead    Light intensity adjustment error 13ch
 Exeae    Light intensity adjustment error 14ch
 Exeaf    Light intensity adjustment error 15ch
 Exeb0    Light intensity adjustment error 16ch
 Exeb1    Light intensity adjustment error 17ch
 Exeb2    Light intensity adjustment error 18ch
 Exeb3    Light intensity adjustment error 19ch
 Exeb4    Light intensity adjustment error 20ch
 Exeb5    Light intensity adjustment error 21ch
 Exeb6    Light intensity adjustment error 22ch
 Exeb7    Light intensity adjustment error 23ch
 Exeb8    Light intensity adjustment error 24ch
 Exeb9    Light intensity adjustment error 25ch
 Exeba    Light intensity adjustment error 26ch
 Exebb    Light intensity adjustment error 27ch
 Exebc    Light intensity adjustment error 28ch
 Exebd    Light intensity adjustment error 29ch
 Exebe    Light intensity adjustment error 30ch
 Exebf    Light intensity adjustment error 31ch
 Exee0    Incorrect command has been input
 Exee1    The temperature of the LD block is greater than 28degrees
 (Temperature at the periphery of the optical unit > 35degrees. Temperature of the environment > 28degrees)
 Exee2    Temperature at the periphery of the optical unit is greater than 35degrees
 (Temperature of the environment > 28degrees)
 Exee3    The temperature of the radiating fin is greater than 55degrees
 (Temperature at the periphery of the optical unit > 35degrees. Temperature of the environment > 28degrees)
 Exee4    It is just before a recording head has dew
 (Temperature of the LD block >= 22degrees)
 Exee5    The temperature of the LD block is less than 5degrees
 (Temperature at the periphery of the optical unit < 17degrees. Temperature of the environment < 18degrees)
 Exee6    0-7ch in signal line is break detect
 Exee7    8-15ch in signal line is break detect
 Exee8    0-15ch in signal line or DOTCLK signal line is break detect
 Exef0    Recording head processing task is now processing another message
 Exef2    Recording head unit is not running
 Exef3    Recording head data check sum error occurred when data was uploaded
 Exef4    Recording head data address error occurred when data was uploaded
 Exef5    LD calibration cannot process because temperature of LD block is too low
 Exef6    A command was sent to the exposure head. But, no answer was returned from the exposure head
 Exfa0    System error (stack overflow)
 Exfa1    Floating point arithmetic error
 Exfa2    Divide-by-zero error
 Exfa3    System error (semaphore)
 Exfb0    Flash memory erase error
 Exfb1    Flash memory erase error (during verification)
 Exfb2    Flash memory write error
 Exfb3    Incompatible flash memory