Linotronic 560

 Boot Status Messages
 Code:                                               Description:
 INIT RECORDER START  Recorder initialization started
 INIT RECORDER 0  Time loop of about 45s. (LES power on delay)
 INIT RECORDER 1  Polygon drive initialized using the last X resolution setting
 INIT RECORDER 2  Film feed initialized using the last Y resolution value
 INIT RECORDER 3  Current density set
 INIT RECORDER 4  Cutter initialization, move to cutter stop, if necessary
 INIT RECORDER DONE
 Recorder is ready
  Recorder initialization completed successfully
 (In Test mode, not all initialization routines are executed; certain
 errors may not be recognized)


   
 
     

 Status Messages During Operation
 Message:                                      Description:
 LI5 ENABLE
 LI5 interface enabled; parameters can be defined also from
 the LT55 panel (equal priority)
 PROCESS ACTIVE
 A process is active; no other process can be started. The
 process may be aborted by (SHIFT) STOP
 USER STOPPED
 Process aborted by the user
 FILM ADVANCING
 Film is being advanced
 FILM ADVANCE DONE
 Film advance completed
 FILM CUTTING  Film is being cut
 FILM CUT DONE  Film cutting completed
 INSERT FILM  Insert film into the film transport system. Wait until the
 message is displayed
 ADJUST FILM   Adjust the film. Unlock the film drive (right-hand red button)
 Centre the film. Lock the film drive
 FILM LOADING  Film is being loaded into the film transport system
 CONTINUE FILM LOAD  Film loading is continued. Film advance with film cut
 FILM LOAD DONE   Film loading completed. Insert take-up cassette
 ALREADY FILM  Film already loaded
 ABORT FILM LOAD  Film loading aborted. Photomaterial was not recognized
 FILM UNLOADING  Film unloading is started
 FILM UNLOAD DONE  Film unloaded from the film transport system
 CUT BEFORE UNLOAD  Film loading aborted. Cut material
 NO FILM SUPPLY  No film available in film transport system (end of film)
 WARNING END OF FILM  End of film approaching alert
 FILMLOAD > CMD-
 ERROR
  Photomaterial error. (Try REC 1)
 IMAGING  Output in progress
 IMAGING DONE  Output completed
 IMAGING DONE  Recorder test printout in progress
 TEST IMAGING DONE  Recorder test printout completed
 DENSITY JOB STARTED  Density test printout in progress (several densities)
 DENSITY JOB DONE  Density test printout completed
 ACTUAL JDNS
 STARTED
  Density test printout in progress (current density only)
 ACTUAL JDNS
 STARTED
  Density test printout completed
 CHANGE TAKEUP CASS  Change the take-up cassette
 NO TAKEUP CASSETTE  Take-up cassette not inserted
 TAKEUP CASS FULL  Take-up cassette is full; material is cut automatically
 REMOVE TAKEUP
 CASS
  Remove the take-up cassette - cut has been performed
 CHECK CUTTER POS  Cutter not at stop position. Do not close the film transport
 system to avoid damaging the cutter
 WARNING DENSITY  The selected density is too low. SOL detection may not be
 possible 
 TAKO ACTIVE  Calculation of tacho correction
 WARNING TAKO  Polygon tacho correction not successful
 WARNING FILM DRIVE  Zero mark of the film transport roller not found
 RANGE OVERFLOW  Zero mark of the film transport roller not found
 X.LM + X.M > F.WIDTH  Left margin plus measure greater than film width
 NO VALID RESOLUTION  The defined resolution is not supported
 NO RES FOR LI2 STNG  The defined resolution is not allowed with the current LI2
 Parameters. Select 16 MHz async mode in the INTERFACE
 menu; the RIP must also support the 16 MHz mode 
 OLP FORCED CUT  Forced cut of material is being executed because the
 maximum  galley length of the online processor is reached
 OLP AUTOMATIC CUT  Auto film cut for online processor is being executed

 Status Error Messages
 Message:                                               Description:
 RIP, NOT CONNECTED  A backend defined as imagesetter cannot see the RIP
 RIP > NOT SELECTED  RIP and recorder not synchronized
 RECORDER > TIME OUT  START signal did not trigger an interrupt. No light at SOL?
 RECORDER > TIME OUT  SOL missing. SOL-threshold, but no SOL recognized. Light intensity too low?
 SOL amplifier failure 
 NO LIGHT > DENSITY  Selected density too low. SOL is not recognized. Increase the density 
 SPINNER > TIME OUT  Selected density too low. SOL is not recognized. Increase the 
 DENSITY >TIME OUT  At present not used
 ERROR TAKO > WRITE  Tachometer correction error on writing the correction values.
 Has been Polygon fault
 ERROR TAKO >READ  Tacho correction error on reading the correction values
 TAKO ACTIVE  Tachometer correction iteration. Please wait
 ERROR > CUT [120]  Cutter not at stop position. Limit switch still active
 ERROR > CUT [121]  Cutter time-out. Cutter blocked
 ERROR > CUT [122]  Film advance in progress. Cutting not allowed
 ERROR > FILM LOAD  Film loading error
 OLP NOT OPERABLE  Online processor not available. Check connection
 OLP NOT READY  Online processor not ready. Check online processor
 OLP BRIDGE  Failure of bridge to online processor
 LI2 >SENDER NOT OPR  LI2 sender not operable. SOPR deactivated
 LI2 >SCAN OVERRUN  Too many pixels in transferred scan line
 LI2 >SENDER ERROR  Recorder aborted the job at the receiver operable signal (ROPR). A new output request
 is issued but the old sender page signal (SPGE) of the sender is still active 
 LI2 >TIME OUT  Abort of an LI2 connection to the recorder by time-out. This error may, at present,
 not occur because a time-out is not defined
 LI2 WITHOUT LI5  Output is not controlled via the LI5 interface. Output is started by pressing the START
 key
 LI5 >NO PARTNER  LI5 partner (RIP) not available
 LI5 >TIME OUT  Time-out on the LI5 interface. This error may at present not occur because a time-out
 is not defined 
 LI5 >OVERRUN  DUART overrun on the LI5 interface. LI5 interface may not be served by the recorder 
 LI5 >PARITY ERR  Parity error on the LI5 interface
 LI5 >FRAMING ERR  Framing error on the LI5 interface
 LI5 >SYNCHR ERR  Software synchronization error on the LI5 interface
 HARD-REV TOO LARGE  Hardware revision number too large for firmware
 HARD-REV TOO SMALL  Hardware revision number too small for firmware
 HARD-REV TOO SMALL  Wrong flag returned by application process
 PLEASE RESET  Press both Reset keys

 
EEPROM Errors
 Message:                                               Description:
 EEPROM >INIT  EEPROM initialization. Default values are assumed
 EEPROM >INIT  EEPROM update. After installation of a new program on the REC1 board the EEPROM
 data has been defaulted
 EEPROM >NEW INIT  A new EEPROM was installed. Default values assumed
 EEPROM ERROR  General EEPROM error
 EEPROM >CHECKSUM  Wrong checksum of EEPROM data
 EEPROM OVERFLOW  EEPROM full. (All three EEPROM blocks were used and may no longer be written)
 Install new EEPROM
 EEPROM >OLDSOFTWARE  Firmware older than EEPROM data structure. Install new firmware
 EEPROM >OLD EEPROM  EEPROM data structure obsolete. The firmware automatically converts the data
 structure. Check the data
 EEPROM>TOO OLD  EEPROM structure very obsolete. The firmware automatically converts the data
 structure. Check the data
 EEPROM>TOO OLD  EEPROM defect. Replace the EEPROM

 NVRAM Errors
 Message:                                               Description:
 NVRAM >TOO OLD  NVRAM data structure obsolete. Reinitialze the LT55
 NVRAM >OLDSOFTWARE  Firmware older than NVRAM data . Install new firmware
 NVRAM >FATALERROR  Fatal NVRAM error; initialize the LT55 panel
 NVRAM >ERROR  General NVRAM error, initialize LT55
 NVRAM >MESSAGE ERR  General NVRAM error, initialize LT55